• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Allowing your cat to enter and go out of the house at their own pace is a good idea to keep it physically and mentally active. A flap can help reduce the frequency of accidents due to toilets, making it easier for cats to leave the home when required.

Measure the Door

A cat flap lets your pet to go and come whenever they want without opening the door for them. This makes it ideal to keep them inside when you're at home or away and helps keep unwanted pests out of the home too!

You should measure the door to ensure that you get the right size cat flap. There are many sizes available. You can then ensure that the cat flap is the right size for the door you have. Otherwise, it could be too big or small, and your Cat Flap Bifold Doors could have difficulty using it.

Use a ruler to determine the width at several locations along the edge of the door. You should also take measurements of the door's height in a couple of places. A door that is too tall can cause your cat to perform an acrobatics routine each time it uses the flap.

If you're not sure how to measure a door, it might be best to seek assistance from a glazier or someone who performs this type of work regularly. They will be able determine whether your door is suitable for cat flaps and advise you on what size flap you should purchase.

Mark out the shape of the hole on your door after you have taken the measurements. This will assist you when you're cutting the hole, and will save you money!

Make sure to put the hole in the right place. If you are fitting the cat flap onto the patio door, it is important that the hole doesn't get too close to the hinges. This could lead to leakage or problems with the seal.

If you have a glass door it is best to leave this task to a professional glazier. It can be a challenge to fit a cat flap inside the glass pane, and you may discover that the process causes it to break and lose its weatherproof seal.

Measure the Cat

A cat flap allows your pet to move around as they want without you having to leave him on his own. It can also stop draughts entering your home, which is not good for your cat as well as you.

If you have a uPVC door or composite door, it could be difficult to install the cat flap. These kinds of doors are usually constructed of different materials than traditional wooden or uPVC doors and the process of installing them is quite different too. Before you consider fitting a cat flap in your uPVC or composite door, make sure that it's compatible, and that you have consulted the manufacturers as alterations may invalidate any warranties.

These doors are generally designed to last and are tough with insulation. This makes them more resistant to the elements of weather than other doors, however they can be difficult to fit a cat flap into. If you're uncertain about whether your uPVC or composite door is able to accommodate the cat flap, make sure you consult with a professional joiner prior to beginning.

You'll need to take their height in order to ensure that they can fit through the door. This will be easiest when they're sleeping or calm, so that they're not moving around too often. Once you've determined their height, take a measurement of the distance between their stomachs and the floor to determine where the bottom of the cat flap should be. You can then mark this position on the door.

If your uPVC or composite door is made from metal (either steel or aluminium), you'll need to be extremely cautious when cutting it with power tools. The drilling process can make cracks, particularly if the area is made of toughened glass. This is why it's highly advisable to hire an expert glazier to install your cat flap inside a pane of glass. This will stop the glass from breaking or becoming brittle. A glazier will also be able to provide you with a cat flap hole that is less likely to break and safer for your cat to use.

Cut the Hole

A good cat flap fitting flap will come with a template drawing that can be used to mark the spot on your door where the hole will be. If it doesn't, create your own with a thin piece of paper (tracing papers are great). After the shape has already been penciled on the door, you can utilize your spirit level to make sure that it is horizontal. This will allow your cat flap to properly fit into the opening and stop it from being in a position to slide open or close.

Then, use your jigsaw to cut out the pattern that is marked on the door. Make sure you are using a blade that is suitable for use on uPVC doors. Usually, it will be marked as such If not, ask the staff at your DIY store for advice. Once you have the hole drilled and the flap section is in place, put it against it and push it open to make sure that the flap's movement is smooth. If it binds at any point, make use of a file or a rasp to fix this.

Check that there aren't any gas or electric pipes inside the door you plan to cut into. The jigsaw may damage them. Also, be aware of any handles, or other fixtures that are on the door which must be removed to accommodate the cat flap. Be careful not to damage these items while cutting.

Most people who fit a cat flap on their own will have a standard solid uPVC door and will not have to worry about any of these problems. If your door is made of wood or has a decorative part that is not easily removed, it will make the task.

It is always worthwhile seeking expert help from a cat flap fitter for these kind of jobs as it is essential to do them done right to avoid potential issues in the future. It is essential to get it right as doing it wrong can damage the door and void the warranty.

Install the Flap

After you've cut your hole, place the flap to check whether it opens and is able to fit. If you notice any points that stick or catch or stick, use a hand-file or sandpaper to file them down until they fit perfectly and open without any problems. Make sure the flap is perfectly flush with the door.

If your tool doesn't have a template, you can make use of thin paper such as tracing or acetate. Place the paper against the door and draw an area on which you'll want to position the flap (this will serve as your cutting guide). Then using the pencil lines you've drawn on the door, mark out four screw holes in the corners of the flap - these are the screw holes that you'll use to secure it in place.

Most uPVC doors are solid and therefore simple to cut into. But, if your door is made from GRP or a composite, this may be more difficult. If you're not familiar with this, it's recommended that you hire a professional. They can also help you determine whether or not your particular door is suitable for cat flap installation.

You can fit an opening for a cat flap in composite doors but it's important to check with the manufacturers or a professional joiner prior to making any changes since any modifications to these types of doors could invalidate the warranty. If you decide to complete the work yourself, keep in mind that it could be a messy job and could be dangerous.

You'll need to use an instrument like a grinder or a saw to cut through composite doors rather than just the GRP. This is a potentially dangerous task, and you'll require extra care to avoid damaging the door. It's worth noting that it's more difficult to create a hole in a door glass than a uPVC door or solid wood door.