• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

The RS232 driver and receiver use separate conductors on the serial cables, enabling full duplex communications. The RS422 driver and receiver use separate differential conductor pairs on the serial cables, enabling full duplex communications. 5 Volt supply by a dual RS232 driver chip that has a built-in charge pump voltage multiplier. The master is in charge of designating which receiver is on at any one time. The terminal’s serial receiver chip re-inverts the signal to its positive sense. RS232 uses inverse logic; that is, a positive bit at the 68HC11 UART is inverted by the onboard RS232 driver chip and appears as a negative signal on the serial cable. Although the RS232 protocol specifies functions for as many as 25 pins, each communications channel requires only three for simple serial interfaces: TxD1 (transmit data), RxD1 (receive data), and DGND (digital ground). The primary channel’s UART translates the bit-by-bit data on the serial cable into bytes of data that can be interpreted by the QED-Forth Kernel or by your application program. Serial 2 is implemented by a software UART in the controller’s QED-Forth Kernel that uses two of the processor’s PortA I/O pins to generate a serial communications channel.

The QScreen Controller has two serial communications ports: a primary serial port called Serial 1 that supports both RS232 and RS485 protocols, and a secondary serial port called Serial 2 that supports RS232. Note that the local and the remote must share a common ground, so a minimum of 3 wires are required for full duplex RS232 communications: a transmit wire, a receive wire, and a common ground. Note that the local and the remote must share a common ground, so a minimum of 3 wires are required for half duplex RS485 communications: a pair of transceive wires and a common ground. Because a single pair of conductors is used for both transmission and reception, RS485 is useful for multi-drop applications in which a master communicates with multiple slave serial devices, or nodes. Each RS422 driver transmits a differential pair of output signals at 0 and 5 volts. Done that establishes the RS485 receive mode is coded such that it waits until all queued (pending) characters have been transmitted before the driver chip is taken out of transmit mode. Each of the two channels on the UART Wildcard implements two 16-character FIFOs, one for outgoing characters and one for incoming characters.

Each of the two channels on the UART Wildcard can be configured for RS232, RS422, or RS485. Like RS232, the data bits are transmitted in reverse order, with the least significant bit transmitted first. The RS485 protocol uses differential data signals for improved noise immunity; thus RS485 can communicate over greater distances than RS232. The Serial 1 port can be configured for either RS232 or RS485 communications at up to 19200 baud. The Serial 2 port is dedicated to RS232 communications at up to 4800 baud. Because differential signals have inherently better signal-to-noise properties, reliable RS422 communications can be sent over much longer distances compared to RS232. In addition to its physical characteristics, RS485 cables also have specific electrical properties that allow for differential signaling, enabling reliable data transmission over longer distances compared to other communication protocols. The master can instruct a single slave to go into transmit mode, and then the master can put itself into receive mode, thereby allowing the master to retrieve data from the slave. For example, at 4800 baud (bits per second), each bit lasts about 200 microseconds (µs), and if communications are full duplex (e.g., if the QScreen Controller echoes each incoming character), then there is a serial interrupt every 100 µs or so.

Owing to hardware constraints, if modem handshaking is needed on UART channel 1, then channel 1 must be configured for RS232, and channel 2 cannot be configured for RS232 communications. RS232 allows both communicating parties to transmit and receive data at the same time; this is referred to as full duplex communications. It is optimal for outdoor use cases that need reliable data collected over years. RS232’s greatest benefit is its universality; practically all personal computers can use this protocol to send and receive serial data. After configuring the SPI system to communicate on a properly connected network of devices, sending and receiving data is as simple as writing and reading a register. But these are signal wires and the network always requires a return path. The USB cable requires a specific programming package and does not support freeport communications. Its simplest implementation requires only three wires: one to transmit serial data, a second to receive serial data, and a third to provide a common ground reference. Hardware is interfaced to the SPI via three PORTD pins named SCK, MOSI, and MISO brought out to pins 7, 8, and 10 on the Wildcard Port Header (see Appendix B). The Serial 1 port is implemented with the 68HC11's on-chip hardware UART (Universal Asynchronous Receiver/Transmitter).

If you cherished this article and you also would like to get more info regarding rs485 cable nicely visit our own web-site.