• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage Replacement Key

The key in many Kia models has an electronic keyless entry system built into. This key usually resembles a remote control and is able to be replaced by a new one purchased from a kia keyless entry remote (Utahsyardsale.com) dealer or a locksmith.

Key fobs can stop working due to a number of reasons, including batteries that are dead, worn-out buttons signals, signal interference or water damage. Here are some guidelines on how to get your Kia Sportage replacement key working again.

How to replace a remote key or smartkey

No matter if your Kia is equipped with an intelligent key, remote key, push to start key or a regular non-transponder steel key The battery inside these keys will eventually need replacing. This is particularly in the event that your car displays a message telling that the smart key or remote has low battery power.

It's a fairly simple procedure. To replace the keyfob battery remove the mechanical key from the slit on the back of the fob. Then, push the cover off. A small screw is found inside the key fob that holds the battery in its place. Remove the old battery by detaching the screw with a small screwdriver. Install the new battery and then close the gap on the key fob.

Once the key fob has a fresh battery and you've tested it, press the locks and unlock buttons. If the doors lock and unlock according to your expectations, then you're good to go! You can now make use of Kia's hands-free lock/unlock function whenever your fingers get chilly or you need to do some errands in Brandon.

Note: Certain key fobs could need to be programmed (transponder chips or smart keys). This requires a computer that is available only to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of metal), do not need programming. If your key requires to be programmed, you will need to be aware of the number printed on the tag of the key code and save it in a safe place.

How to replace the battery

If the Kia key fob is unable to respond to pressing the lock or unlock button, it is most likely that the battery is low. A low battery could cause other issues such as the check engine light flashing on or delayed engine cranking. It is easy to replace key fob batteries by using only two tools.

Make sure you turn off your vehicle and shut all doors prior to beginning. Find the small metal or plastic piece on the bottom of the key fob. Move it until the key is released. Then, you can insert the key in the door handle of the driver to open your car.

To replace the key fob battery, take off the cover from the back and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery and then orient the new battery to ensure that the "+" positive side is facing your face and the "-" negative side is facing the fob's electronic contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damaging or breaking the metal contacts.

Once the new battery is installed and the key fob is turned on, turn it off and on in the ignition repeatedly until the door locks cycle. Then you can test your 2013 kia sorento key replacement key fob to see whether it's working again.

How do you replace a smart key

You may have either a standard keyfob, or a Smart Key based upon the model of kia rio replacement key fob Sportage. The smart key is equipped with an embedded mechanical key blade, unlike the standard key fob, which does not. Both types of key fobs have batteries that will eventually have to be replaced. Luckily, this is quite simple and takes only two minutes.

Before you start it is essential to ensure that you are on a level surface with enough lighting and that your Kia is turned off. Keep in mind that the fob is made up of small pieces that could be thrown off should you not be careful.

The first step is to locate the small release button on the back of the lower part of the fob. It could be a circular button or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open then you can remove the old battery, and replace it. The new battery should be a CR-2032, and can be bought online or from your local auto parts store. Once you're done, your key fob should permit you to lock and unlock your vehicle even if it's not running.

How do you replace the mechanical key

The Kia keyfob is a great convenience, allowing us to lock or unlock our car with just pressing one button. However, like all devices there are issues with it occasionally. There are steps to take to troubleshoot these issues and keep our key fobs in good working condition in the long run.

A dead or drained battery is one of the most common problems. This can cause your device to stop working or work intermittently. If this is what you are experiencing it is time to replace the battery a new one.

If this doesn't fix the issue Try using a standard flathead screwdriver to open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a new one.

Once the new battery is in, shut and open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that will fit in the slot). Test the key fob to make sure it is working properly. If the fob still not working, contact an authorized locksmith or dealer to solve the issue. To avoid locking outs in the future, ensure you purchase an emergency key that will work on all trunk and door cylinders.