• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they do not get rusty or decay.

It is important to clean and oil UPVC doors and windows regularly. This will help prevent unnecessary repair costs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and may even be fatal. It is important to make sure that your windows are in good condition.

Single-pane windows are fairly simple to replace and typically fit into frames of the past easily. However If you have double pane windows that are secured by internal beading, it will be more difficult to remove the old panes and put in new ones. In this case, you will need to locate some plastic spacers to help the new pane to fit properly into the window frame.

Wearing eye protection and thick gloves is a must when you are planning to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards of glass fall onto the fabric and not onto the floor and could be trampled under.

Once the glass has been removed from the window, it's best to cover the gap with packaging tape or duct tape to stop water and drafts from getting into the home until a professional comes out and repair the window. It also acts as a barrier, preventing any intruders from getting access into your home. If the gap is particularly large, you may be interested in a security door that has an integrated window, window repairs since it offers the best of both worlds.

2. Sagging

uPVC is durable and energy efficient alternative to timber sash window. However, over time they can suffer from a variety of problems including sagging. A window that is sagging can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to shrink, it's important to act quickly to stop the issue from becoming worse.

Repositioning the hinges can help fix a window that is sagging. You'll first need to open the windows so you can reach the frame. Then, you can remove the hinges on the top and bottom with a screwdriver and adjust them counter-clockwise or clockwise. Close your window to check the fit after having moved your hinges. If you're satisfied with the fit, you can tighten the screws to ensure they remain in the right place.

If you are unable to reposition the hinges, you might require replacing the seal. Rubber seals may dry out and lose their elasticity over time, leading them to lose their tightness. If this happens, it's crucial to replace the seal as quickly as possible to ensure your uPVC windows are waterproof and secure from draughts.

uPVC handles may also become loose. This is usually due to screws that have been removed over time, but it can also be caused by the handle mechanism getting worn out. It's a good thing that it's simple to repair the loose uPVC window handle yourself. First, you'll need to shut the window and perform a test fitting. The corner joints of the sash need to align with the casing joint. If it isn't then you can use the screwdriver to loosen up the handle. Then, you can turn the mechanism to position.

3. Water Leaks

It is essential to take action if awake each day to discover mouldy walls and floors that are wet. The leaks of water from windows do not only lead to the degrading of the structure of your home but also hamper your efforts to regulate the temperature within your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

It is a fairly easy fix that can be completed by any skilled DIYer. Depending on the severity of the problem the caulking that was used up may need to be removed before a new layer of caulk is applied. It is essential to remember that when it is about uPVC window repairs you should not be tempted to 'over-caulk in order to make the area more difficult to clean and could reduce the efficiency of your energy.

It is important to check that any drainage holes are clear of debris and that the sill pan has been angled properly so that it drains away from the window. In more serious situations, you might have to consider replacing the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in damp conditions and can quickly spread throughout the house.

It is also important to keep in mind that if the leakage originates from the glass in your double glazing repairs near me glazed windows it may be more likely to be an issue with the glass seal, rather than the frame or sagging. A uPVC specialist can easily fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or loose and blow open with a breeze It could be hinges that are at the fault. Any competent DIYer can replace these in a matter of minutes.

Nearly every home in the UK will have either top hung or side hung upvc window repairs near me windows that are hinged and like any mechanical part they can wear down over time. It is essentially a very simple process but it can be easier to do if you have someone to assist in holding the frame in place.

It is also important to ensure that the uPVC hinges are being opened and closed in the right direction. This can be done by looking for the arrows on each hinge, this shows which way the window should open.

The issue could be caused by opening the window improperly or due to a poor installation at the factory. It is usually possible to fix the issue by sending us a picture on our website. We will be happy to give you advice.

It is also essential to grease the hinges regularly. Applying an engineering lubricant that is light to the hinges is a great method of doing this. We recommend using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It also decreases the risk of a window getting stuck and stop corrosion. The ideal time to perform this every year. WD40 or other solvent-based lubricants are not recommended as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by several different factors. Firstly the hinges, again because of wear and tear, may become displaced, which will cause an opening to appear between the sash and the frame. These can be easily fixed by giving them a good clean, but when they're beyond repair, it may be necessary to have them realigned or replaced. Secondly the interlock, this is on the hinge side of the window and can be misaligned. Again, it is possible to give them a good clean, but in certain cases, it may be necessary to get them replaced.

These seals are susceptible to wear and tear or become damaged over time, allowing air escape. Replacement of these with high-quality weatherstripping can help prevent draughts. Replace the windows made of upvc with low-emissivity glasses. This will help control indoor temperatures and lessen the risk of draughts.

The last way to reduce drafts effectively is to use a Draught-excluder. These are usually fabric tubes filled with a filler, which can be placed over your window sill. They can help keep cold air out and keep your home warm and cozy!

With a bit of regular maintenance and repairs your windows made of upvc will provide excellent security and insulation for your home. However, it is important to recognise that windows last for a certain period of time and there may come the point when it's more economical to replace them than repair them. If you are experiencing problems with your upvc windows, it is always recommended to seek assistance from a professional immediately.